Search found 17 matches
- 17 May 2022, 20:34
- Forum: Hardware and software hacking
- Topic: Gigatron Clone Ideas
- Replies: 46
- Views: 8070
Re: Gigatron Clone Ideas
PAL16V8 is metal fuse PROM. GAL16V8 is EEPROM, HAL16V8 is mask ROM. 16V8 architecture is always the same.
- 30 Jan 2022, 22:56
- Forum: Kit assembly gallery
- Topic: Another successful Gigatron build
- Replies: 4
- Views: 3188
Re: Another successful Gigatron build
All I can confirm is that all my ROMs are available, but some RAM is not available. For example, AS6C62256-70, UT62256-70, HM62256LP-12 are all available. However HM62256-15 and UM62256-70 are not available. HM62256-15 is too slow, you need 70ns. HM62256LP-12 is also too slow, you were lucky that i...
- 18 Nov 2021, 15:01
- Forum: Hardware and software hacking
- Topic: Can I build with HC rather than HCT series ICs ?
- Replies: 5
- Views: 2179
Re: Can I build with HC rather than HCT series ICs ?
My Gigatron is a wild mixture of LS, HC and HCT, whatever was available.
You have to keep in mind that HCT can be driven by LS, HC and HCT, but HC can only be driven by HC and HCT but not LS. The logic high output level of LS is too low for HC.
You have to keep in mind that HCT can be driven by LS, HC and HCT, but HC can only be driven by HC and HCT but not LS. The logic high output level of LS is too low for HC.
- 23 Oct 2021, 23:24
- Forum: Hardware and software hacking
- Topic: Gigatron OS - Some progress and a (solved) hardware mystery.
- Replies: 23
- Views: 15770
Re: Gigatron OS - Some progress and a (solved) hardware mystery.
It is true that PALs were common these times, but the Gigatron was designed as a TTL-only system. It even has diode matrix decoders. If Marcel and Walter had used GALs from the beginning, ALU and control logic would be significantly smaller. The whole system would fit onto an eurocard. But that was ...
- 23 Oct 2021, 19:28
- Forum: Hardware and software hacking
- Topic: Gigatron OS - Some progress and a (solved) hardware mystery.
- Replies: 23
- Views: 15770
Re: Gigatron OS - Some progress and a (solved) hardware mystery.
Did I understand correctly -- your Gigatron OS does not use the zeropage switching, so that it also works with the classic expansion board?
I want to keep my Gigatron GAL-free as long as possible
I want to keep my Gigatron GAL-free as long as possible
- 22 Aug 2021, 17:11
- Forum: Hardware and software hacking
- Topic: Gigatron vs. Arduino Uno
- Replies: 5
- Views: 3580
Re: Gigatron vs. Arduino Uno
When I connect my software (or any other terminal software) through the (usb)serial to the Uno board I receive some weird chars (i.e.: "p°W8(ÓñS[¹$ß¡‹™[u"). If I send any ASCII char to the Arduino, the X1 red LED blinks but nothing happens. First get the serial communication working. Unti...
- 10 May 2021, 11:35
- Forum: Hardware and software hacking
- Topic: Possible ways of speeding up the Gigatron
- Replies: 32
- Views: 11049
Re: Possible ways of speeding up the Gigatron
The Gigatron was designed as a "TTL Microcomputer". Now there are some expansion ideas based on GALs. If you accept programmable logic in your highspeed Gigatron this could significantly shorten the critical path.
- 21 Nov 2020, 17:35
- Forum: Kit assembly gallery
- Topic: My Gigatron! It very almost works! (Help!)
- Replies: 7
- Views: 9066
Re: My Gigatron! It very almost works! (Help!)
Instead of feeding the shift register you could also add a parallel input to your Gigatron. Use a 74HCT574 or 374 octal flipflop and connect its outputs to BUS0..7. Clock (pin 11) goes to SER_LATCH (/VSYNC). Cut the /IE signal where it enters U39/74HCT595 at pin 13 and insert a three-pin jumper here...
- 21 Aug 2020, 16:09
- Forum: Hardware and software hacking
- Topic: microtron
- Replies: 42
- Views: 25340
Re: microtron
Up only: 74xx461, 463, 590, 591, 592, 593
Up and down: 74xx469, 579, 869, 867
74HC(T)590 should be the most common one.
Up and down: 74xx469, 579, 869, 867
74HC(T)590 should be the most common one.
- 20 Aug 2020, 17:25
- Forum: Hardware and software hacking
- Topic: microtron
- Replies: 42
- Views: 25340
Re: microtron
74HC393 is a ripple counter, like the 4040. Better use a 74HC163.